您的位置: 首页 > 国外标准 > 美国材料与试验协会ASTM >  ASTM F 2144-2009  开口式深油煎锅性能的标准试验方法
 

ASTM F 2144-2009  开口式深油煎锅性能的标准试验方法

标准编号:ASTM F 2144-2009
分享到:

中文标准名称:开口式深油煎锅性能的标准试验方法
英文标准名称:standard test method for performance of large open vat fryers
标准状态:现行有效
代替标准号:ASTM F2144-07
语言:英文版,中文版
发布日期:2009-10-01
实施日期:2009-10-01
标准类别:美国材料与试验协会ASTM
标准页数:17
标准简介:

The energy input rate test is used to confirm that the fryer under test is operating in accordance with its nameplate rating.

Fryer temperature calibration is used to ensure that the fryer being tested is operating at the specified temperature. Temperature calibration also can be used to evaluate and calibrate the thermostat control dial.

Preheat energy and time can be used by food service operators to manage their restaurants'' energy demands, and to estimate the amount of time required for preheating a fryer.

Idle energy rate and pilot energy rate can be used to estimate energy consumption during non-cooking periods.

Preheat energy, idle energy rate, pilot energy rate, and heavy- and light-load cooking energy rates can be used to estimate the fryer''s energy consumption in an actual food service operation.

Cooking-energy efficiency is a direct measurement of fryer efficiency at different loading scenarios. This information can be used by food service operators in the selection of fryers, as well as for the management of a restaurant''s energy demands.

Production capacity is used by food service operators to choose a fryer that matches their food output requirements.

1.1 This test method covers the energy consumption and cooking performance of large-vat open, deep fat fryers. The food service operator can use this evaluation to select a fryer and understand its energy efficiency and production capacity.

1.2 This test method is applicable to floor model gas and electric fryers with 50 lb (23 kg) and greater fat capacity and an 18-in. and larger vat size.

1.3 The fryer can be evaluated with respect to the following (where applicable):

1.3.1 Energy input rate (10.2),

1.3.2 Preheat energy and time (10.4),

1.3.3 Idle energy rate (10.5),

1.3.4 Pilot energy rate (10.6, if applicable),

1.3.5 French fry cooking energy rate and efficiency (10.9),

1.3.6 French fry production capacity and frying medium temperature recovery time (10.9),

1.4 This test method is not intended to answer all performance criteria in the evaluation and selection of a fryer, such as the significance of a high energy input design on maintenance of temperature within the cooking zone of the fryer.

1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

文件格式:纸质版或者PDF电子版(用Acrobat Reader打开)或Word版本doc格式
PDF格式 ASTM F 2144-2009 开口式深油煎锅性能的标准试验方法 免费下载 Word格式 ASTM F 2144-2009 开口式深油煎锅性能的标准试验方法 免费下载免费标准下载
文件大小: KB
添加时间:2012/11/23
 
相关免费标准
 
 
本类标准下载排行
 
 
本类最新免费标准
 
免费标准下载网 |标准分享网 |联系我们
版权所有:www.ZBGB.org